Anyone fitted these uprated springs to their 906?
https://www.wrs.it/en/fork-springs-kit/ ... 89-91.html
Search found 116 matches
- Thu Feb 10, 2022 7:54 pm
- Forum: 906 Paso
- Topic: Hyperpro Fork & Shock Springs Kit - Ducati 906 Paso
- Replies: 0
- Views: 55970
- Thu Feb 10, 2022 7:44 pm
- Forum: 906 Paso
- Topic: spacer between airbox and velocity stacks necessary?
- Replies: 5
- Views: 9914
Re: spacer between airbox and velocity stacks necessary?
Another thing that upsets the air going into the air filter housing and engine running is if you remove the 2 inlet pipes/trumpets...can't remember why I removed them , but the bike ran very poorly...
- Fri Jun 22, 2018 9:32 pm
- Forum: 906 Paso
- Topic: Renovation complete
- Replies: 13
- Views: 26834
Re: Renovation complete
I like the cold air intakes for the air filter....
- Tue Jun 27, 2017 4:35 pm
- Forum: 906 Paso
- Topic: Restoration Photographs
- Replies: 4
- Views: 9658
Re: Restoration Photographs
Forgot that, have spare brand new wheels and michelin tyres, however the tyres fitted now have only covered 100 miles from new....
- Sat Jun 24, 2017 2:08 pm
- Forum: 906 Paso
- Topic: Restoration Photographs
- Replies: 4
- Views: 9658
Restoration Photographs
Just a few photos of my Duc...off the road since 2012... Before http://i242.photobucket.com/albums/ff261/GTEPETE/ducatioct2007001.jpg http://i242.photobucket.com/albums/ff261/GTEPETE/ducatioct2007003.jpg After New chain and sprockets http://i242.photobucket.com/albums/ff261/GTEPETE/DSC07433_zpsiwahw...
- Sat Jun 24, 2017 1:48 pm
- Forum: 906 Paso
- Topic: Front wheel/Fork seals/oil capacity
- Replies: 5
- Views: 8914
Re: Front Fork seals/ photograpghs added
Have stripped forks and found it all in good order...very straight forward, used a hot air gun to help removal of old seals but... can anyone confirm the small aluminium sleeve end (LHS) is fitted correctly with taper facing towards the main shaft (the one with short spring)...it dropped off as my 9...
- Mon Jun 05, 2017 7:19 pm
- Forum: 906 Paso
- Topic: Front wheel/Fork seals/oil capacity
- Replies: 5
- Views: 8914
Re: Front wheel
thanks englishstiv, my look seals ok, it was just the dust seals that were cracked...I'm not keen to strip forks down at the moment....unless is it realistic to remove the seal without stripping out? have read if you use heat and screws, then seal can be pulled out...
- Sun Jun 04, 2017 7:05 pm
- Forum: 906 Paso
- Topic: Front wheel/Fork seals/oil capacity
- Replies: 5
- Views: 8914
Re: Front wheel
Worked it out, looking at parts page, the LH washer is incorporated in the speedo drive....now need to strip the forks to replace seals....
- Wed May 31, 2017 9:08 pm
- Forum: 906 Paso
- Topic: Front wheel/Fork seals/oil capacity
- Replies: 5
- Views: 8914
Front wheel/Fork seals/oil capacity
My rebuild continues...and so do the questions....I have now removed front wheel to clean discs and replace fork seals. Question 1...should there be a axle washer on axle LH fork, where speedo drive sits? I found one on RHS, but not LHS, exploded picture in workshop indicates they should be one...bu...
- Wed May 24, 2017 7:13 am
- Forum: 906 Paso
- Topic: Rear Brake Light switch rubber boot
- Replies: 4
- Views: 7863
Re: Rear Brake Light switch rubber boot
Its only the boot I need, I have ordered one meant for Triumph. Will feedback to confirm if it is a good fit..
http://www.ebay.co.uk/itm/GENUINE-Trium ... oHiZ5ZccRw
http://www.ebay.co.uk/itm/GENUINE-Trium ... oHiZ5ZccRw
- Tue May 23, 2017 8:00 pm
- Forum: 906 Paso
- Topic: Rear Brake Light switch rubber boot
- Replies: 4
- Views: 7863
Rear Brake Light switch rubber boot
Hi all, just bled rear caliper, noticed the rubber boot that fits over the electric terminals for brake light switch has disintegrated. Is this available from Ducati, or is there an alternative from another model??
- Wed May 03, 2017 9:24 pm
- Forum: 906 Paso
- Topic: Nigel Mansell 906....
- Replies: 4
- Views: 8048
Re: Nigel Mansell 906....
Mc tool, you buy it and I will look after it until you can collect!!!
- Tue May 02, 2017 8:35 pm
- Forum: 906 Paso
- Topic: Nigel Mansell 906....
- Replies: 4
- Views: 8048
- Tue Apr 25, 2017 10:36 am
- Forum: 906 Paso
- Topic: Cush drive/carrier removal
- Replies: 3
- Views: 6921
Re: Cush drive/carrier removal
Just as Paso750 says above, cush drive came out nice and easy, plan to replace sprocket lock nuts with aircraft spec stainless ones.....despite these minor set backs I am really enjoying working on my Duc with this forums help and looking forward to getting back on the road for the summer.... :D htt...
- Sun Apr 23, 2017 2:00 pm
- Forum: 906 Paso
- Topic: Chain adjustment
- Replies: 6
- Views: 8556
Re: Chain adjustment
The mistake I made was that I was turning the concentric clockwise, so axle was at one o'clock position max rather than anti clockwise to 4 o'clock position where you get maximum chain slack before the caliper hits the axle bracket (it hits sooner turning clockwise)...took out two links (106) today ...