Thanks everybody for the answers.

I'll try to replace in a short time cause i don't have time now.
And yes,changing the position of two plates decrease the noise, but i don't remember it. I don't mind cause i like original clutch sound.

Thanks.

Have you done the quiet clutch mod? A really good easy mod( depending on how mechanicy you are ) that shuts up the rattley clutch and all you need is one or two old friction plates Have you done the quiet clutch mod? Do you refer to the special tool to move the clutch? I don't have but i know how t...

Hi there, It's time to replace the cluch of my baby(has nearly 60k kms). The gears are ok but it's so noisy now. What do you recomend me?(brands/n of teeth...)How can i know if i have to change the springs and the drum...And where can I buy it. In my country is easy to find it, but i would like diff...

Hello , This is my 1st post after many hours of reading all of this great info . Thank you to all who give to this forum . I am the original owner of a '92 907ie (25,000 mi) . I am waking her up after a lengthy slumber and all has gone well ... until today .All of my questions are related to 'insid...

Here added ethanol too and at the moment no problem. I'll pray to continue in the same way haha!!! About the size of the pump i have no idea(i know how is mine) but remember seeing some by internet time ago. If you have any problem to find it: Fuel Pump REF4304411A that's the reference about 907i.e ...

After the fuel clamp issue was resolved (see above) I assumed I was all set. Today took a ride out to Jacksboro, TX for a "Herd Burger". On the way back my partner passed a truck pulling a trailer at about 70mph. When there was an opening I down shifted two gears, whacked the throttle ope...

Congratulations!!! nice bike and enjoy it!!! But you are wrong about there is only one registered in U.K. doesn't matter! Looking by internet i've seen some more a while ago. Derek has confirmed it!! In my country there are very few, probably less than 10 and two or three ridding only but i don't kn...

Probably the best way to build up the cable would be with solder. You will need to thoroughly degrease the end of the cable then use a bath of molten solder to dip it in after dipping it in a flux first. Killed spirits is the best flux for this. Once you have built up a layer of solder you can then...

Hi everybody, sorry for the waitting. :-( :-( Thanks Derek and Willo for your answers :thumbup: . I didn't resolve the problem yet cause too much time without the bike on and decided mount all again and ride this summer around mi country. The drive rounds perfectly but when connect the cable a minim...

Thanks @paso750, But the cable is ok, i bought a new one thinking was the cable,normally the connections turns round, but not now. I tested all the sistem without de cable cover and works but when there's a minimum pressure, friction on it, the drive still moving but not the cable, then i suposse is...

I don't know why i can't upload the picture.

Hi again, The count rev gear doesn't work ok,the interior where the cable go in slip, normally is the cable that turns round but no this time and my Ducati dealer says doesn't produce Anybody knows where can i find it? I'm waiting some answers from other ducati foro but no answers at a moment At par...

Thanks both.

But first i have to perfectionate my english hahaha!!!

Hi Vainika, just saw your post...Did you resolve the supports of the ECU? i just bought a couple on a Ducati dealer.
Easy to find it.

Bye.

Hello everybody, I'm Duc77 and i'm owner of 907 i.e from '91. I'm from Catalonia. I followed the web many years ago and registered last summer but i don't know why, never found enough time to log in and chat with you...hahaha! Suppose cause most of the problems i resolved on Ducati chats. :-P Well, ...