Engine ready to go back in

discussions specific to the 750 Paso

Moderators: paso750, jcslocum

Post Reply
User avatar
jcslocum
paso grand pooh-bah
Posts: 1714
Joined: Mon Jul 19, 2004 12:00 am
model: 750 Paso
year: 1988
Location: Eastern Shore, MD
Contact:

Engine ready to go back in

Post by jcslocum »

This fall my 750 Paso had a failure of the output (sprocket) shaft bearing. I picked up a used bottom end and just finished transferring all of the parts from the other engine over. I hope to get the engine back into the frame today and maybe get her running tomorrow.

I may take the old engine apart to see just how much damage has been caused by the failure. From what I can see from the outside and by looking into the engine now that the pistons are out, there is very little loose metal in there.
User avatar
Skins
paso grand pooh-bah
Posts: 1304
Joined: Tue Oct 26, 2004 12:00 am
model: 750 Paso
year: 1988
Location: Kapiti, New Zealand

Post by Skins »

So you've got your barrels, pistons, and heads on a new (used) bottom end and gearbox, eh Jon? Did you set new ignition timing on the new bottom end, or are you just going to see how the new one feels? Let us know how it goes.

I have found the *sweet spot* on my chain again at just on 25mm slack, and once again have a total absence of vibration.
User avatar
jcslocum
paso grand pooh-bah
Posts: 1714
Joined: Mon Jul 19, 2004 12:00 am
model: 750 Paso
year: 1988
Location: Eastern Shore, MD
Contact:

Post by jcslocum »

I had to transfer the timing pickups but not the bracket. I'm hoping it's OK.

Do you have a procedure for setting the timing??
User avatar
Skins
paso grand pooh-bah
Posts: 1304
Joined: Tue Oct 26, 2004 12:00 am
model: 750 Paso
year: 1988
Location: Kapiti, New Zealand

Post by Skins »

:thumbup:

The timing should be good, jon. All you can do is align with the reference marks on the bracket - the rest is up to the igniter module.

The last time I took the timing apart, the bike felt a bit flat after I had put the motor back in. I must have slightly missaligned the marks a bit - parallax, I guess. So I took the motor out again and changed the alignment slightly. I must have got it right the second time because she ran as good as if not better than before. I could not check the advance dymanically because I didnt have a strobe light.

It might be possible to take the side casing off without removing the motor, but for some reason, I did.
User avatar
Skins
paso grand pooh-bah
Posts: 1304
Joined: Tue Oct 26, 2004 12:00 am
model: 750 Paso
year: 1988
Location: Kapiti, New Zealand

Post by Skins »

How did it go, jon?
steele

Post by steele »

Well you can certinly take the side cover off a 906 when the engine is in the frame so cant see any differance on 750 just need a puller which is very easy to make :thumbup:
User avatar
jcslocum
paso grand pooh-bah
Posts: 1714
Joined: Mon Jul 19, 2004 12:00 am
model: 750 Paso
year: 1988
Location: Eastern Shore, MD
Contact:

Post by jcslocum »

Skins wrote:How did it go, jon?
Nothing done yet. I was abducted to other projects around the house.
User avatar
Skins
paso grand pooh-bah
Posts: 1304
Joined: Tue Oct 26, 2004 12:00 am
model: 750 Paso
year: 1988
Location: Kapiti, New Zealand

Post by Skins »

OK, jon, well I hope it FLIES. If she doesn't go as well as she did before, it can only be the timing, eh?
User avatar
jcslocum
paso grand pooh-bah
Posts: 1714
Joined: Mon Jul 19, 2004 12:00 am
model: 750 Paso
year: 1988
Location: Eastern Shore, MD
Contact:

Post by jcslocum »

Skins wrote:OK, jon, well I hope it FLIES. If she doesn't go as well as she did before, it can only be the timing, eh?
I'm hoping she just runs good!!
User avatar
paso750
paso grand pooh-bah
Posts: 5558
Joined: Sun Jul 18, 2004 12:00 am
model: 750 Paso
year: 1987
Location: southern Germany

Post by paso750 »

John,

check out the Haynes stuff in the download section if you want to kow how to adjust the timing.
It`s not for the Paso but the engines of Monster/SS are about the same.

Gerhard
User avatar
jcslocum
paso grand pooh-bah
Posts: 1714
Joined: Mon Jul 19, 2004 12:00 am
model: 750 Paso
year: 1988
Location: Eastern Shore, MD
Contact:

Post by jcslocum »

Gerhard,

Glad to see you've made it over from the mail list. I still do both.

I'll download the haynes info and check it out. It would be nice to do a static timing before putting it in and having it running. Thanks.
Post Reply