Search found 50 matches
- Fri May 13, 2022 2:29 pm
- Forum: 907IE
- Topic: 906 fairings to 907IE
- Replies: 2
- Views: 6640
Re: 906 fairings to 907IE
The side fairings are the same between 906 and 907. Obviously the nose sections look different but they will directly swap between both models.
- Sun Sep 06, 2020 12:59 pm
- Forum: 750 Sport and 900SS
- Topic: Later USD triple trees on 89/90 frame
- Replies: 7
- Views: 11950
Re: Later USD triple trees on 89/90 frame
I put a spacer under the lower race when I put a set of Showa forks from a 1995 900SS on a Sport
- Tue Dec 20, 2016 11:34 pm
- Forum: 907IE
- Topic: Paso 20mm swingarm pivot modification
- Replies: 23
- Views: 20518
Re: Paso 20mm swingarm pivot modification
Thanks for your non-constructive comments.
Maybe you should post some pictures of stuff you have built.
Maybe you should post some pictures of stuff you have built.
- Tue Dec 20, 2016 1:54 pm
- Forum: 907IE
- Topic: Paso 20mm swingarm pivot modification
- Replies: 23
- Views: 20518
Re: Paso 20mm swingarm pivot modification
how did you solve it with the bearings in the engine case? I assume the 999 engine originally uses a 20mm swingarm pivot. The 999 does use a 20mm pin, but I did not use the 999 cases. The 999S have deep sump cases and those wouldn't fit with the bodywork. So I am using ST3 cases with the 999 intern...
- Tue Dec 20, 2016 1:50 pm
- Forum: 907IE
- Topic: Paso 20mm swingarm pivot modification
- Replies: 23
- Views: 20518
Re: Paso 20mm swingarm pivot modification
Speedmade, don`t mind me asking but seeing that the thread of the 20mm pivot is longer I wonder which part of it sits in the frame. Hope you get what I mean. (if it`s the threaded part it could cause radial play, which may be gone if all is tightened up, but still...) No issue. The full 20mm sectio...
- Tue Dec 20, 2016 4:52 am
- Forum: 907IE
- Topic: Paso 20mm swingarm pivot modification
- Replies: 23
- Views: 20518
Re: Paso 20mm swingarm pivot modification
The frame will be powder coated once I finish the rest of the modifications to install the 999S motor
- Mon Dec 19, 2016 11:32 pm
- Forum: 907IE
- Topic: Paso 20mm swingarm pivot modification
- Replies: 23
- Views: 20518
Re: Paso 20mm swingarm pivot modification
This should make for a much stiffer chassis.
- Mon Dec 19, 2016 11:31 pm
- Forum: 907IE
- Topic: Paso 20mm swingarm pivot modification
- Replies: 23
- Views: 20518
Re: Paso 20mm swingarm pivot modification
I had to turn the head of the new pivot down slightly to fit down the frame pocket.
On the other side I had to source a small OD flange nut.
Everything fit so I could install the black plastic caps.
On the other side I had to source a small OD flange nut.
Everything fit so I could install the black plastic caps.
- Mon Dec 19, 2016 11:28 pm
- Forum: 907IE
- Topic: Paso 20mm swingarm pivot modification
- Replies: 23
- Views: 20518
Re: Paso 20mm swingarm pivot modification
Modifications to the bearings in the swingarm were pretty straight forward. Sourced some new bearings and made a few new spacers.
- Mon Dec 19, 2016 11:25 pm
- Forum: 907IE
- Topic: Paso 20mm swingarm pivot modification
- Replies: 23
- Views: 20518
Re: Paso 20mm swingarm pivot modification
Measuring the inside of the frame I realized that there would be very little surface area left so I had cups machined that I welded over the original pivot area.
- Mon Dec 19, 2016 11:23 pm
- Forum: 907IE
- Topic: Paso 20mm swingarm pivot modification
- Replies: 23
- Views: 20518
Re: Paso 20mm swingarm pivot modification
My plan was to bore out the frame but it was impossible to fit in a milling machine. So I made fixtures that allowed me to drill out the holes in steps.
- Mon Dec 19, 2016 11:22 pm
- Forum: 907IE
- Topic: Paso 20mm swingarm pivot modification
- Replies: 23
- Views: 20518
Re: Paso 20mm swingarm pivot modification
I found a 20mm axle from some Japanese bike was very close in spec to the Paso pivot.
- Mon Dec 19, 2016 11:20 pm
- Forum: 907IE
- Topic: Paso 20mm swingarm pivot modification
- Replies: 23
- Views: 20518
Paso 20mm swingarm pivot modification
I found that the Paso has a 15mm swingarm pivot. That is very small especially considering that all other Ducati models since 1990 they have used a 20mm pivot. So I decided that I wanted to upgrade.
This would require modifications to the frame and the bearings in the swingarm.
This would require modifications to the frame and the bearings in the swingarm.
- Thu Oct 08, 2015 5:02 pm
- Forum: for sale / for trade / want to buy
- Topic: FS: pair of Limited mirror assemblies
- Replies: 1
- Views: 2856
- Sat Sep 26, 2015 11:18 am
- Forum: for sale / for trade / want to buy
- Topic: FS: NEW billet alloy clutch basket for 750/906
- Replies: 2
- Views: 3171