Search found 90 matches
- Tue Feb 14, 2017 12:35 am
- Forum: 907IE
- Topic: starter Solenoid issues
- Replies: 5
- Views: 6599
Re: starter Solenoid issues
Is it a high enough current rating for the 907 ? Do you reckon the solenoid is the main restriction in the starter circuit (other than the load of the starter motor itself)? I seemed to go through a couple of solenoids until i swapped in a set of those big diameter starter cables... the only issue ...
- Mon Jan 30, 2017 10:12 am
- Forum: for sale / for trade / want to buy
- Topic: Want to buy stickers for a 1991 907ie
- Replies: 5
- Views: 6008
Re: Want to buy stickers for a 1991 907ie
thanks guys!
- Wed Jan 25, 2017 7:46 am
- Forum: for sale / for trade / want to buy
- Topic: Want to buy stickers for a 1991 907ie
- Replies: 5
- Views: 6008
Want to buy stickers for a 1991 907ie
Hi guys, I'm about to embark on repainting my '91 907ie and would like to source a set of the stickers (Ducati, Desmo, 907ie) etc that will be under a coat of clear on the final version. I can see a couple of providers around the world but wanted to know if anyone had had good experience with any pa...
- Wed Jan 11, 2017 12:30 am
- Forum: Off-topic
- Topic: Tailor made 16" 5-spoke alloy rims (Campagnolo style)
- Replies: 6
- Views: 15158
Re: Tailor made 16" 5-spoke alloy rims (Campagnolo style)
This shouldn't be that hard... the custom Harley market does it a fair bit (admittedly usually heavy on the style and not on the performance). There's a company in Australia http://dragway.com.au/ that is known to do one off / limited edition wheels and with the EU to AU$ rate at the moment that mig...
- Fri Jan 06, 2017 1:23 am
- Forum: 750 Paso
- Topic: paso con mikunis 750,,,no funciona bien
- Replies: 17
- Views: 19786
Re: paso con mikunis 750,,,no funciona bien
Hello again, after getting my ducati Paso to work acceptably, began to fail, when I went from being dead, to get first gear and try to roll with it, began to fail and did not let up revolutions, was momentarily in a Cylinder. I have the impression that there is an electric fault that ends in a comb...
- Mon Jan 02, 2017 1:25 am
- Forum: 750 Paso
- Topic: paso con mikunis 750,,,no funciona bien
- Replies: 17
- Views: 19786
Re: paso con mikunis 750,,,no funciona bien
is not only a matter of Airflow, it could also be turbolence caused by the speed that is effecting the airflow I agree, you only have to meddle with a modern Japanese bike airbox and see how quickly you loose low speed throttle response or get strange flat spots. I remember fitting a GSXR1100 filte...
- Mon Jan 02, 2017 1:09 am
- Forum: 750 Paso
- Topic: Multi-blocks/connectors Paso ..... inventory
- Replies: 1
- Views: 4885
Re: Multi-blocks/connectors Paso ..... inventory
Hi, Did someone make an inventory of all multi-blocks/connectors used on the wiring loom? I will make some adjustments to the loom and am even considering making a fully new one. Good advise is always welcome! These guys were selling some NOS complete wiring harnesses a little while ago http://www....
- Sat Dec 31, 2016 5:48 am
- Forum: 750 Paso
- Topic: paso con mikunis 750,,,no funciona bien
- Replies: 17
- Views: 19786
Re: paso con mikunis 750,,,no funciona bien
what does "v & h in the air" mean? Except to the pilot jets it`s the original 750SS jetting used on an engine with an aftermarket 2in1 exhaust and foam filters on the Mikuni (without an airbox)? It is definitely running lean. I'd agree... without changing jets you could just restrict ...
- Sat Dec 31, 2016 5:46 am
- Forum: 750 Paso
- Topic: paso con mikunis 750,,,no funciona bien
- Replies: 17
- Views: 19786
Re: paso con mikunis 750,,,no funciona bien
Yeah, my spanish is rudimentary but i never expected a carbie would translate as an egg.
:-)
- Thu Dec 29, 2016 11:34 pm
- Forum: 750 Paso
- Topic: paso con mikunis 750,,,no funciona bien
- Replies: 17
- Views: 19786
Re: paso con mikunis 750,,,no funciona bien
To me this sounds like a tuning issue at high load, large throttle which lots of people have commented on the forum. have you read the tech article - http://forums.ducatipaso.org/viewtopic.php?f=1&t=705 (go down the page to the mikuni section) which will help you work out what you have and what ...
- Mon Dec 26, 2016 7:22 am
- Forum: 907IE
- Topic: Merry Christmas Cam Belts
- Replies: 5
- Views: 6251
Re: Merry Christmas Cam Belts
Does the bike like listening to sweet tunes on the radio?
- Mon Dec 19, 2016 9:59 pm
- Forum: Off-topic
- Topic: More metal and screws
- Replies: 12
- Views: 22027
Re: More metal and screws
Yeah, but you want to keep the leg if you can... Sorry to sound grim.
- Sun Dec 18, 2016 11:28 pm
- Forum: for sale / for trade / want to buy
- Topic: MIRRORS AND INDICATORS for sale!
- Replies: 3
- Views: 4310
Re: MIRRORS AND INDICATORS for sale!
hi guys im in australia and on ebay at the moment there is a guy selling indicator lenses for $12 aud and replica mirrors for $89 aud go to ebay australia type ducati paso cheers mick Yes, that's me and it's cheaper to buy them through the forum (no ebay fees). viewtopic.php?f=4&t=7536 Just PM ...
- Mon Dec 12, 2016 2:52 am
- Forum: Off-topic
- Topic: More metal and screws
- Replies: 12
- Views: 22027
Re: More metal and screws
That's going to send the airport metal detector off the scale!! . Not so much if it's stainless, or even (which they do sometimes these days) titanium. At least mine never do... But that's a big ouch so wishing well for you for the recovery and can imagine it feels better already if only because ev...
- Wed Dec 07, 2016 5:44 am
- Forum: 750 Paso
- Topic: anodizing footpegs & brackets?
- Replies: 8
- Views: 9507
Re: anodizing footpegs & brackets?
Apparently some shops say that anodizing these cast parts would not have a good result. G. Really? You need a nice clean and smooth surface to get a good effect but as long as the surface is pretty clear it should be fine. Any small ridges get "more" or "less" annodized (it's a ...