ducatipaso.org

Hello all . . .

I am in need of some parts for my Paso 750:

Lefthand side oil cooler cover (attaches to fairing)****ACQUIRED
Rubber fittings for both oil coolers (in the fairings) **** ONLY NEED 1 SET NOW
Left side oil cooler (either side will do actually)****ACQUIRED
Fairing for headlamp****ACQUIRED
Left and right flasher/mirror assemblies****ACQUIRED
Battery strap****N/A
Rear brake foot lever with rubber
Front rubber gromet for gas tank to frame****ACQUIRED
Rear tail peice (on top of the taillight)****ACQUIRED
130/60 ZR16 front tire
Speedometer cable****ACQUIRED
Tachometer cable
Both oil filters
Weber carburetor rebuild kit
Rear fender/license plate holder

I AM interested in any other compatible parts you may have for sale as well - just run it by me.

Thanks!

there is no battery strap on the Paso.
You should add your location to your profile, that would be helpful if looking for parts.

G.

I got a complete Weber carb.

I might have a tail piece (have to look it up in the shed).

And a set of black wheels with tyres (front so so state, rear reasonable).

How much for the weber?

Don't really know what's worth.
When I look around on the web I see prices from around E100 (somewhere on this forum) till E300 when It's used on a Buggy or Fake American Musclecar.

Say E100?

What is the serial number on the weber and do you know what jetting it has. For 100 euro it will have to have exactly what I am looking for to be worth the price
In particular I need to know which emulsion tubes your weber has installed. Be nice to know which auxilliary venturi tubes you have as well for future reference.
Also which main venturis.

I'll look it up for you and post some pics...

Hope fredskidoo don't mind us doing business.
fredskidoo, Weber kits are available on ebay for a few dollars.

most weber parts can be had at http://www.piercemanifolds.com/
They also are in California

Update on WTB: Paso Parts.

As of today it looks like I have acquired:
tail piece
front tire
speedo cable
rubber gromets to hold oil coolers

Thanks to Higgy for the Weber link, Desmo_Demon for a speedo cable
and Ed at guzzitech.com for the tail piece.

No worries Harry and Higgy . . .

easy

Its a bit dirty after 20 years of Paso service.
Absolutely no corrosion..

very nice,but not what I am looking for,gonna take a pass..........sorry

It's ok, but how it looks inside?
You need to pull the cap!

fredskidoo wrote:Rear brake foot lever with rubber
Front rubber gromet for gas tank to frame

I have a spare brake lever, but I think it is a little bent, or something else may be wrong with it, but I forget. I'll check on it for you....

I may have one of the front rubber grommets for the tank in my spares inventory. I'll have to look. If not, I can get you the dimensions so you can probably make one of your own.

fredskidoo wrote:Both oil filters

You mean the spin-on filter and the prefilter screen?...The spin-on filter is the same as what the newer ones use, so you can find that at any dealer or buy an aftermarket filter, like a K&N KN-153 filter. The prefilter screen may still be available through Ducati but will probably be expensive. Finding anyone parting out a Paso on eBay, especially engine parts, may produce a person with one that will sell the prefilter screen to you.



I received your payment and will be getting the other parts out to you either this afternoon or tomorrrow. I'll shoot you a PM when they go out.

Hi.
i have a few spares i am getting rid of,
-front fairing bracket
-front mudguard
-rear cowling
-headlight
-taillight (yellow indicators)
-rear footpegs
-rear grabrail (needs rechroming)
-repo near side mirror / blinker assembly (left hand side)
-near side handle bar (left hand side)
-fuel sender
-new brake lever
-new front sprockets x2
-new rear sprocket
-rear axle
-new rear disk
-brake master cylinder and lever
-original webers x2
-airbox
-used front disks
-wiring harness
-ventura rack
-staintune pipes

if your interested in any of these let me know

thanks
Rodney